Bass Guitar Setup: The Steps in the Right Order
A bass guitar setup is done in a fixed order: fresh strings, neck relief with the truss rod, string height at the bridge, pickup height, and intonation last. Each step affects the next, so changing the order means doing work twice. Most players can do all five at home. Nut slots and fret leveling are jobs for a technician.
A setup decides how easy a bass is to play. It matters most for beginners, because high strings or buzz make a bass hard to play and are easy to mistake for a lack of skill. That is why I recommend a professional setup right after you buy a first bass in my guide to the best bass guitar for beginners. This page explains what that setup includes, so you can do it yourself or know what to ask for.
Free: Slap Bass Starter Pack
5 video lessons with slow-motion takes, drum loops and tabs. Enter your email and download it right away.
What Do You Need for a Bass Setup?
| Tool | Used for |
|---|---|
| Electronic tuner | Tuning and intonation |
| Steel ruler with small markings | String height and pickup height |
| Feeler gauges or a business card | Neck relief |
| Truss rod key | Neck relief, usually supplied with the bass |
| Small hex keys and screwdrivers | Saddle height, saddle position, pickup screws |
| Capo (optional) | Holding the string at the 1st fret while you measure relief |
Before you start, check the maker’s published setup specifications for your bass. Most big brands publish them, and they are the best target for the measurements below.
Step 1: Why Do You Start a Setup With New Strings?
Every adjustment depends on string tension. Old strings are worn and uneven, which throws off intonation, and a different gauge or brand changes the tension on the neck. Set up the bass on the strings you will actually use, in the gauge you plan to keep, and tune to pitch. If you have never done it, my guide on how to change bass strings shows the whole job.
Step 2: How Do You Set Neck Relief?
Relief is the slight forward curve of the neck that leaves room for the vibrating string. Hold the E string down at the 1st fret, or put a capo there, and hold it down at the last fret. Measure the gap between the string and the top of the 8th fret. Fender recommends about .012 inch (0.3 mm) for necks with a 9.5 to 12 inch fingerboard radius, and about .014 inch (0.35 mm) for vintage-style 7.25 inch necks.
If the gap is too big, tighten the truss rod a little. If it is too small or zero, loosen it. Small turns only, and let the neck settle before you measure again. The full method, including which way to turn and when to stop, is in my guide to bass truss rod adjustment.
Step 3: How Do You Set String Height on a Bass?
String height, or action, is the gap between the bottom of the string and the top of the fret, usually measured at the 17th fret. On most bass bridges, each saddle has two small height screws. Raise or lower both screws of a saddle by the same amount so the saddle stays level, then retune and measure again.
On a curved board, set the middle saddles slightly higher than the outer ones, so the strings follow the curve of the fingerboard and the gap to the frets is about the same on every string. The lowest setting that does not buzz through the amp at your normal attack is the right one for you. Players with a strong attack need a little more height than players with a light touch. If the bass starts to buzz, my guide on bass fret buzz helps you find where it comes from.
Do not use the truss rod to change string height. The rod sets the curve of the neck, and the saddles set the height. Mixing the two jobs fixes one problem by creating another.
Step 4: How High Should Bass Pickups Be?
Pickup height changes volume, balance and sustain. Too close and the magnet pulls on the string, which can make notes sound wobbly or out of tune, especially on the low E at the upper frets. Too far and the bass sounds weak.
Fret the last fret of the E string and measure from the bottom of the string to the top of the pickup, then do the same on the G string. Start from the maker’s published measurement and adjust by ear. Listen for even volume across all strings and for the low E to sound clean when you play it high up the neck. On a bass with two pickups, set them to similar volume so the blend control works across its whole range.
Step 5: How Do You Set Intonation on a Bass?
Intonation makes the notes higher up the neck play in tune. Tune the open string. Play the harmonic at the 12th fret, then fret the note at the 12th fret and compare both on a tuner.
- If the fretted note is sharp, move the saddle back, away from the neck.
- If the fretted note is flat, move the saddle forward, toward the neck.
Move it in small steps with the screw at the back of the bridge, retune the open string after every move and compare again. Repeat on each string. Intonation comes last because every earlier step changes it.
Which Parts of a Setup Should a Technician Do?
Two jobs need special tools and experience. Cutting nut slots: if the open strings buzz or sit too high, the nut slot depth is the fix, and a slot cut too deep means a new nut. Fret work: leveling, crowning and polishing frets fixes single notes that buzz when everything else is set correctly.
A technician will also check the electronics, tighten loose jack and tuner nuts and look for cracks or a twisted neck. If you are not sure about any step above, a shop setup shows you what a well-adjusted bass feels like. After that you can keep it there yourself.
When Does a Bass Need a New Setup?
- After you change string gauge or brand.
- When the season changes and the strings feel higher or start to buzz.
- After a flight or a long trip in a cold car.
- When notes higher up the neck sound out of tune with the open strings.
- When you buy a used bass, whatever it looks like.
Frequently Asked Questions
What is included in a bass guitar setup?
Fresh strings, neck relief with the truss rod, string height at the bridge, pickup height and intonation. A technician may also check the nut slots and the frets and tighten loose hardware.
In what order should you set up a bass?
Strings first, then neck relief, then string height, then pickup height, then intonation. Each step changes the ones after it, so intonation always comes last.
How often does a bass need a setup?
Whenever it starts to play differently: buzz, higher action, notes out of tune higher up the neck. Changes of season and changes of string gauge are typical reasons.
Can I set up my own bass?
Yes, for strings, relief, string height, pickup height and intonation. You need a tuner, a ruler, feeler gauges or a business card, the truss rod key, hex keys and a screwdriver. Nut and fret work is best left to a technician.
Does a setup make a cheap bass better?
It makes it play better. A budget bass with a good setup is often easier to play than an expensive one with a bad setup. It will not change the basic sound of the pickups or the wood.
How do you set intonation on a bass?
Compare the 12th fret harmonic with the fretted note at the 12th fret. If the fretted note is sharp, move the saddle back, away from the neck. If it is flat, move it forward. Retune after every move.
New to Bass? Start Here
Start free with my step-by-step guide on how to play bass guitar and the free Slap Bass Starter Pack. After your first few weeks, send me a video of your playing for a $25 review, and I will show you what to fix before bad habits set in. If you would rather learn with a teacher live, book a 60-minute lesson over Zoom.
Free Slap Bass Starter Pack →Video review, $25 →Live lesson, $60 →