How to Change Bass Strings: Step by Step, Without Mistakes

How to Change Bass Strings: Step by Step, Without Mistakes

To change bass strings, loosen and remove the old string, feed the new one through the bridge, pull it to the tuning post, measure enough length for two to three wraps, bend it sharply and cut past the bend. Put the end into the post, wind downward, tune up, then stretch the string and retune until it holds pitch.

Changing bass strings is not hard, but bass strings are thick, long and not cheap, so a mistake costs more than on guitar. Two mistakes cost a string: cutting it too short and cutting it before bending it, which can loosen the outer winding. This guide walks through the whole process in the order you do it. When to change strings and which type to buy is covered in my bass guitar strings guide, so this page is only about the job itself.

Free: Slap Bass Starter Pack

5 video lessons with slow-motion takes, drum loops and tabs. Enter your email and download it right away.

Free download right after signup. Privacy

What Do You Need to Change Bass Strings?

ItemWhat it is for
A new set of stringsSame gauge as before, unless you plan to adjust the bass
Wire cuttersBass strings are too thick for scissors
Electronic tunerClip-on or app, for tuning the new set
Clean dry clothWiping the fretboard, body and new strings
String winder (optional)Saves time when loosening and winding

Check the scale length on the packet before you open it. Most basses are long scale, 34 inches, and use long scale strings. Short scale, medium scale and extra long scale basses need strings made for that length, otherwise the full-thickness winding ends up where it has to go into the post hole, or the thin end of the string lands over the nut.

How Do You Remove the Old Bass Strings?

Take a photo of the headstock first, or look carefully at how the old strings are wound. It shows you which way each string goes around the post and where it enters the hole, which is the easiest way to get it right on your bass.

Turn the tuning key to loosen the string until it is completely slack. Do not cut a string that is still at pitch, because it can whip back toward your hand or face. Once it is slack, unwind it from the post and pull it out through the bridge.

If you remove all the strings at once, this is the moment to wipe the fretboard and the frets with a dry cloth and clean under where the strings were. My guide on how to clean a bass fretboard covers what to use on each type of wood. Avoid household cleaners on the fretboard. Some players remove one string at a time instead, which keeps the tension on the neck more even. On a standard bass bridge either way is fine. If you take them all off, check neck relief once the new set has settled.

How Do You Put a New String Through the Bridge?

Find the ball end, the small metal ring at one end of the string. Feed the free end through the bridge until the ball end seats in its slot. Depending on the bridge, the string goes in from the back of the bridge or through the body from the back of the bass. On a top-loading bridge, check that the ball end sits flat in its slot before you add tension.

Guide the string over the saddle, over the nut slot and up to the tuning post. Make sure it is in the right nut slot. A thick string sitting in a thin slot will buzz, bind or go out of tune. If your headstock has a string tree, pass the D and G strings under it.

Where Do You Cut a Bass String?

This is the step that matters most. You need enough string for two to three wraps around the post, and no more.

  1. Pull the string tight along the neck, past the tuning post it belongs to.
  2. A common way to measure on a four-in-line headstock is to pull the string to the next tuning post beyond its own. For the last post, or any other headstock, measure two to three inches past the post. Check the packet, some brands print their own advice.
  3. Bend the string sharply at 90 degrees at that point, then cut about half an inch past the bend.

The bend holds the outer winding in place, which is why you bend first and cut second. If you cut first, the winding can start to unravel, and a string with a loose winding sounds dead.

At the tuner end, most bass strings get thinner where the outer winding stops, sometimes under a colored silk wrap. That thinner part goes into the hole in the post, and the full winding wraps around it. The full-thickness part should not be forced down the hole.

How Do You Wind a Bass String on the Tuning Post?

Put the bent end into the hole in the center of the post, down to the bottom. Hold the string near the post with one hand to keep a little tension, and turn the tuner with the other so the string winds downward, each wrap below the last one.

The finished string should leave the post low and in a straight line to the nut. That angle presses the string into the nut slot, which helps sustain and stops rattling. On most basses with all tuners on one side, the string leaves the post on the side facing the center of the headstock and runs straight to the nut. If your bass has two tuners on each side, the strings on the two sides wind in opposite directions. Follow your photo of the old strings.

Two to three wraps are enough. More wraps pile up on top of each other and can make the tuning less stable.

How Do You Tune and Stretch New Bass Strings?

Bring the string up to pitch with a tuner. Standard tuning from the thickest string is E, A, D, G (B, E, A, D, G on a five-string). Tune up to the note, not down to it: if you go past it, drop below and come back up, which keeps the tuner gear under tension so the string holds pitch.

New strings stretch for a while. To speed that up, gently pull the string away from the fretboard at a few points along its length, then retune. Repeat two or three times. The goal is to settle the string at the ball end and on the post, not to test how strong it is.

Play for a few minutes and check the tuning again. It is normal to retune several times on the first day.

Do You Need to Adjust the Bass After New Strings?

If the new set is the same brand and gauge as the old one, usually not. If you change gauge or brand, the tension changes, and the neck can move a little over the next day. Check these three things after a day:

  • Neck relief, the slight forward bow of the neck. A heavier set can pull it forward. My guide to bass truss rod adjustment shows how to measure it.
  • String height at the 12th fret. If the strings feel higher or start to buzz, the relief or the saddle height needs a small change.
  • Intonation. Compare the 12th fret harmonic with the fretted note at the 12th fret. If they do not match, the saddle position needs adjusting.

If any of this feels uncertain, a setup at a guitar shop sorts all three out at once. A good setup makes even a budget bass feel very different, which is why I recommend one in my guide to the best bass guitar for beginners.

What Are the Most Common Mistakes When Changing Bass Strings?

MistakeWhat happensHow to avoid it
Cutting before bendingOuter winding loosens, string sounds dullBend first, cut past the bend
Cutting too shortOnly one wrap, the string can slipMeasure two to three wraps before cutting
Wrong string length for the bassThick winding at the post hole, or the thin end over the nutMatch the strings to your scale length
Wraps going up the postLow string angle at the nut, rattleWind each wrap below the previous one
String in the wrong nut slotBuzz, binding, tuning problemsCheck each string sits in its own slot
Not stretching new stringsTuning keeps droppingStretch gently and retune two or three times

Frequently Asked Questions

Should I change bass strings one at a time or all at once?

Either works on most bass guitars with a standard bridge. Changing one at a time keeps tension on the neck and is a good habit for beginners. Taking all the strings off lets you clean the fretboard, but check the neck relief after the new set has settled.

Where do I cut a bass string?

Pull the string tight past the tuning post, measure enough for two to three wraps, bend it sharply at that point and cut a little past the bend. Never cut a bass string before you bend it, because the outer winding can loosen.

How many wraps should a bass string have on the tuning post?

Two to three wraps, winding downward so the string sits low on the post. Too few and the string can slip, too many and they pile up and can affect tuning.

Which way do bass strings wind on the tuning post?

On most basses with all tuners on one side, the string leaves the post on the side facing the center of the headstock and runs straight to the nut. Follow how the old strings were wound before you take them off.

Why do new bass strings keep going out of tune?

New strings stretch. Tune up, gently pull each string away from the fretboard along its length, tune again, and repeat two or three times. After that the tuning will hold much better.

Do I need to adjust anything after changing bass strings?

If you use the same brand and gauge, usually not. If you change gauge or brand, the tension changes and you may need to check neck relief, intonation and string height.

New to Bass? Start Here

Start free with my step-by-step guide on how to play bass guitar and the free Slap Bass Starter Pack. After your first few weeks, send me a video of your playing for a $25 review, and I will show you what to fix before bad habits set in. If you would rather learn with a teacher live, book a 60-minute lesson over Zoom.

Free Slap Bass Starter Pack →Video review, $25 →Live lesson, $60 →
↑